<sup id="nxtn5"><ins id="nxtn5"><small id="nxtn5"></small></ins></sup>

        <em id="nxtn5"></em>
        <em id="nxtn5"></em><delect id="nxtn5"></delect>

          <div id="nxtn5"></div>
          <menuitem id="nxtn5"></menuitem>

                    <em id="nxtn5"><span id="nxtn5"></span></em>

                      <div id="nxtn5"></div>
                      <em id="nxtn5"></em>
                      <div id="nxtn5"><tr id="nxtn5"></tr></div>
                      <dl id="nxtn5"><ins id="nxtn5"><thead id="nxtn5"></thead></ins></dl>
                       
                      Home  |  About ANYI   |   Products   |   Service + Support   |   Testimonials   |   Expertise   |   Contact   |     
                      Standard Reference
                           Artifacts
                      Precision Step Gauges
                      Swivel Support
                      Module masters
                      Gauge blocks
                      Slide Calipers
                      Digital Calipers
                      Dial Calipers
                      Vernier calipers
                      Digital Scale Units
                      Depth Gauges
                      Digital Depth Gauges
                      Dial Depth Gauges
                      Vernier Depth Gauges
                      Height Gauges
                      Digital Height Gauges
                      Dial Height Gauges
                      Vernier Height Gauges
                      Micrometers
                      Micrometer Heads
                      Outside Micrometers
                      Inside Micrometers
                      Depth Micrometers
                      Indicators
                      Thickness gauges
                      Indicators
                      Special Calipers
                      Special Designs
                      Accessories
                      Clinometers
                      Stands
                      Data Interfaces
                      Surface Plates
                      Others
                      You are here: Home >> Expertise

                      Expertise

                      How to read an outside micrometer

                      Introduction

                      A micrometer generally provides greater precision than a caliper, but can measure a smaller range of lengths. Clean the measuring faces with a clean cloth before and after measurement.

                      Parts of an Outside Micrometer

                      How to Read an Outside Micrometer Graduated in 0.001"

                      Micrometer thimble showing 0.276 inch

                      The pitch of the screw thread on the spindle is 40 threads per inch. One revolution of the thimble advances the spindle face toward or away from the anvil face precisely 1/40" or 0.025", equal to the distance between two graduations on the sleeve. The reading line on the sleeve is divided into 40 equal parts by vertical lines that correspond to the number of threads on the spindle.Therefore, each vertical line designates 1/40" or 0.025". Every fourth line, which is longer than than the others, designates 0.1".The beveled edge of the thimble is divided into 25 equal parts with each line representing 0.001" and every line or every fifth line numbered consecutively. To read the micrometer in thousandths, multiply the number of vertidal divisions visible on the sleeve by 0.025", and to this add the number of thousandths indicated by the line on the thimble which coincides with the central long line on the sleeve.

                      Suppose the thimble were screwed out so that graduation 2, and three additional sub-divisions, were visible (as shown in the image), and that graduation 1 on the thimble coincided with the central long line on the sleeve. The reading then would be 0.2000 + 0.075 + 0.001, or 0.276".

                      How to Read an Outside Micrometer Graduated in 0.01mm

                      Micrometer thimble reading 5.78mm

                      The pitch of the screw thread on the spindle is one-half millimeter(0.5mm). One revolution of the thimble advances the spindle face toward or away from the anvil face precisely 0.5mm. The reading line on the sleeve is graduated above the central long line in millimeters (1.0mm) with every fifth millimeter being numbered. Each millimeter is also divided in half(0.5mm) below the central long line.The beveled edge of the thimble is divided into fifty equal parts, with each line representing 0.01mm and every fifth line being numbered from 0-50. Thus, the reading is given by the number of millimetre and half-millimeter divisions visible on the sleeve plus the number of hundredths of a millimeter indicated by the thimble graduation which coincides with the central long line on the sleeve.

                      Suppose that the thimble were screwed out so that graduation 5, and one additional 0.5 subdivision were visible (as shown in the image), and that graduation 28 on the thimble coincided with the central long line on the sleeve. The reading then would be 5.00 + 0.5 + 0.28 = 5.78 mm.

                      How to Read Vernier Mircometer Graduated in 0.001mm or 0.0001"

                      Micrometer sleeve (with vernier) reading 5.783mm

                      Some micrometers are provided with a vernier scale on the sleeve in addition to the regular graduations. These permit measurements within 0.001 millimetre to be made on metric micrometers, or 0.0001 inches on inch-system micrometers.

                      The additional digit of these micrometers is obtained by finding the line on the sleeve vernier scale which exactly coincides with one on the thimble. The number of this coinciding vernier line represents the additional digit.

                      Thus, the reading for metric micrometers of this type is the number of whole millimetres (if any) and the number of hundredths of a millimetre, as with an ordinary micrometer, and the number of thousandths of a millimetre given by the coinciding vernier line on the sleeve vernier scale.

                      For example, a measurement of 5.783 millimetres would be obtained by reading 5.5 millimetres on the sleeve, and then adding 0.28 millimetre as determined by the thimble. The vernier would then be used to read the 0.003 (as shown in the image).

                      Inch micrometers are read in a similar fashion.

                      When using either a metric or inch micrometer, without a vernier, smaller readings than those graduated may of course be obtained by visual interpolation between graduations.

                       

                      [ << Back ]          

                       
                       
                      CopyRight © 2009 Anyi Instrument Co.,Ltd All Rights Reserved

                      甘肃快三开奖结果今天